You must be logged in to manage your wishlist.
Polymaker CoPA
NYL-COPA-BLACK-175-750
57.80 €
Tax excl.
Polymaker Nylon CoPA 6/6-6 3D printing filament is based on a copolymer of Nylon 6 and Nylon 6,6.
Polyamide 6 (PA6) is the most common extruded polyamide. It stands out in the industry for offering good cushioning and impact resistance properties, as well as good tenacity at low temperatures. It is ideal for example for bearings and gears since they would work silently.
This filament manufactured by Polymaker stands out for its excellent mechanical strength, hardness and thermal resistance of up to 180 °C. Therefore it is equated in thermal resistance to Nylon 180 °C and is placed at only 30 °C of resistance of NylonStrong that supports up to 210 °C of temperature without softening. Therefore, the Polymaker Nylon CoPA 6/6-6 filament becomes one of the most current materials on the market with greater resistance to temperature.
The main advantage of this mixture of Polyamides 6 and 6.6 is that it is designed to provide excellent dimensional stability during printing, with deformations close to zero, which implies that the warping effect is minimal. One of the main printing problems of all nylon filaments is precisely the high warping effect they present, hence the main development effort by Polymaker has been to launch a nylon oriented to the ease of printing.
Therefore, unlike other nylon filaments, Polymaker Nylon CoPA 6/6-6 is easy to print, as it is compatible with most 3D FFF printers on the market without the need for a heated chamber or heated bed at high temperatures.
Like all nylon filaments, the Polymaker Nylon CoPA 6/6-6 filament has a high sensitivity to moisture and should be kept in dry conditions (relative humidity of 20% or less) at all times. It is recommended that the material be used with PolyBox™.
General information |
|
| Material | PA |
| Format | 750 g |
| Density | (ISO 1183) 1.12 g/cm³ |
| Filament diameter | 1.75 / 2.85 mm |
| Filament tolerance | ± 0.05 mm |
| Filament length | (Ø 1.75 mm) ± 278 m / (Ø 2.85 mm) ± 105 m |
Printing properties |
|
| Printing temperature | 270 ºC |
| Print bed temperature | 65 ºC |
| Chamber temperature | ✗ |
| Cooling fan | ✗ |
| Recommended printing speed | 30 - 50 mm/s |
Mechanical properties |
|
| Charpy impact strength | (ISO 179) 9.6 KJ/m² |
| Elongation at break | (ISO 527) 9.9 % |
| Tensile strength | (ISO 527) 66.2 MPa |
| Tensile modulus | (ISO 527) 2223 MPa |
| Flexural strength | (ISO 178) 97 MPa |
| Flexural modulus | (ISO 178) 1667 MPa |
| Surface hardness | - |
Thermal properties |
|
| Melting temperature | 190 ºC |
| Softening temperature | (ISO 306) 180 ºC |
Specific properties |
|
| Transparency | - |
| Chemical resistance | ✓ |
Other |
|
| HS Code | 3916.9 |
| Spool diameter (outer) | 200 mm |
| Spool diameter (inner hole) | 55 mm |
| Spool width | 45 mm |
Nylon PolyMide™ CoPA filament has been designed with the purpose of minimizing the warping effect, but it is still highly recommended to follow certain usage tips.
The use of Raft is recommended to eliminate possible contractions in the printing of the piece. It is also advisable to program the Brim, although the effect will be less and there could be a minimum appearance of warping in the base depending on the geometry of the piece.
To ensure the correct adhesion of the Nylon PolyMide™ CoPA to the base, it's recommended to use BuildTak, DimaFix, PrintaFix or Magigoo PA. In addition to this adhesive it has been developed exclusively for nylon filaments and can be used with a microperforated base, PEI sheets or Kapton Tape. It must be ensured that the adhesion of the first layer is firm and strong to prevent it from peeling off during 3D printing.
At the end of the printing of the piece, if it takes off very quickly from the base, contractions may occur at the base of the piece due to the abrupt change in temperature. Because of this it is advisable to use the 5x5 rule, which consists of just after the end of printing, lower the temperature of the warm bed 5ºC and be at that temperature for 5 minutes. After this period, carry out the same operation again until the temperature of the base is approximately 50 ° C, so that the final piece can be detached without deformation.
Finally, if it is necessary to use support material, it is recommended to use PVA.
Featured properties
Printing temperature
270 ºC
Filament diameter
1.75 / 2.85 mm
Density
1,12 g/cm³
Related products
You must be logged in to manage your wishlist.
You must be logged in to manage your wishlist.
You must be logged in to manage your wishlist.
You must be logged in to manage your wishlist.
You must be logged in to manage your wishlist.
You must be logged in to manage your wishlist.
You must be logged in to manage your wishlist.
You must be logged in to manage your wishlist.
Polymaker CoPA 6/6-6 3D printing filament is based on a copolymer of Nylon 6 and Nylon 6,6.
More shipping options
You will be able to select the payment method you want in the next step of the purchasing process.
FedEx Priority WorldwideDAP Incoterm
0.00 € VAT not included
FedEx Economy WorldwideDAP Incoterm
0.00 € VAT not included
DHL Express WorldwideDAP Incoterm
0.00 € VAT not included
UPS Express SaverDAP Incoterm
0.00 € VAT not included
More shipping options
You will be able to select the payment method you want in the next step of the purchasing process.
FedEx Priority WorldwideDAP Incoterm
0.00 € VAT not included
FedEx Economy WorldwideDAP Incoterm
0.00 € VAT not included
DHL Express WorldwideDAP Incoterm
0.00 € VAT not included
UPS Express SaverDAP Incoterm
0.00 € VAT not included