Find the most suitable 3D printer for your needs.
We guide you to find the best option according to your needs.
Find the most suitable 3D scanner for your needs.
Contact us and we'll get it for you.
Find the most suitable filament for each application.
Find the most suitable resin for each application.
Find the most suitable powder for each application.
Find the most suitable pellets for each application.
Find the accessory you need for your 3D printer.
Find the ideal accessories for your 3D prints.
Do you need more than 3 units? Please, contact us.
Product temporarily out of stock with these characteristics. Select another combination.
We notify you when it will be available:
Sentinel™ Filament Detector
Dyze Design is a company focused on the world of professional 3D printing dedicated to the development and manufacture of components for 3D printers. Within the wide range of products they offer, their high-flow extrusion systems and their high-quality hotends stand out; which allow professional users to print at high temperatures, necessary when working with technical and advanced materials.
As a complement to its extrusion systems, Dyze Design has developed the Sentinel™ filament sensor. A filament sensor is a switch that acts based on the presence or absence of material.
These accessories are designed to eliminate the risk of unfinished prints by detecting the presence of material as well as its movement. For high-volume prints that require multiple spool changes or for specialty filaments prone to breakage, the sensor automatically detects when material has stopped arriving and pauses printing until it recognizes the filament again.
Compatible with a wide variety of FDM 3D printers on the market, regardless of the firmware they use, the Sentinel™ sensor comes as a device just over 3 cm long. Its black metal casing houses a simple circuit board with a light sensor that checks to see if filament is present.
The Sentinel™ filament sensor consumes 31 mA and requires 5V for power. The output logic is 3.3 V and works with 3.3 V and 5 V microcontrollers.
The operation of the system is based on checking the status of a light sensor located on one side of the filament while on the other side there is a light emitter. If at any time there is no filament between the emitter and the sensor, an electronic board turns on a LED as a visual warning and sends a Stop signal through a cable connected to the printer's control board. This command causes the print head to move to one side to make it easier to replace the empty spool with a new one.
The Sentinel™ filament sensor works with all types of filaments: flexible, translucent, opaque, etc. and is available in two versions, compatible with diameters of 1.75 or 2.85 mm. In addition, it is perfectly integrated into the firmware and if it does not detect material in the 3D printer, it will activate the “pause” routine.
As a complement, a dust-proof foam installed inside it makes sure not to allow external elements to enter the extrusion system, and thanks to the two screws provided, the user can install it wherever he wants. A 1m primary cable accompanies the sensor for connection to the 3D printer.
In situations in which unforeseen events must be reduced to a minimum, it is very common to place several sensors in series so that if one fails, the user has another. This is This is achieved through a “daisy chain” wiring scheme. When several sensors are connected in a daisy chain, the system compares the signal from its light sensor with that of the previous sensor. If both signals are positive, a positive output signal will be sent.
Dyze Design has its own Daisy Chain Cable designed specifically for the Sentinel™ sensor.
The Sentinel™ filament sensor is the perfect solution to avoid failed prints when the print volume is large and a large amount of material is needed or for special filaments where the risk of breakage increases.
For a correct operation of the sensor, it is essential that the filaments used have been stored correctly and do not have traces of dust and/or dirt. To avoid this type of situation, it is recommended handle the filaments carefully and try not to touch them with dirty hands to avoid leaving traces of grease. It is also recommended to use PrintDry airtight vacuum sealed filament packs. In addition to guaranteeing the cleanliness of the material, these containers avoid other problems such as humidity, which causes various failures in 3D printing.
It is recommended to check the filter inside the sensor every 1 - 10 Kg, depending on the configuration used by the user. To clean the sensor, a series of steps will be followed:
Placement after the coil: The user must ensure that the joint is stable. You will need to place the sensor on the spool holder, the table or on an element that remains fixed.
Placement before the extruder: The sensor must be attached to the printer, before the extruder. It should not be installed between the extruder and the hotend, as the extruder will not be able to push the filament past the sensor and therefore filament detection will not take place.
More information can be found on the manufacturer's website.
Filament sensor compatible with a wide range of FDM 3D printers on the market.