Display Nav Left

Language:

-30%

Compare

You must be logged in to manage your wishlist.

Extrafill HiPS (Polystyrene)

Ref.: HIPS-EXTRA-NATURAL-175-750

23.00 €

-30%

16.10 €

Tax excl.

Diameter

Format

Colour

Quantity

In stock 8 units available for immediate shipping.
units available for shipping in 0 - 0 days Available for shipment within 0 - 0 days

Product temporarily out of stock with these characteristics. Select another combination.

We notify you when it will be available:

Approximate delivery date: Friday 22 November

Available

Returns

Ask about this product

Extrafill HiPS filament (Polystyrene) (High Impact Polystyrene) is a thermoplastic obtained by polymerizing high impact resistance. It is known as "High Impact Polystyrene" and used as support material ABS or PLA impressions, although for the PLA is more recommended the PVA as support material. The filament Extrafill HiPS (Polystyrene) is a material resistant to heat and with physical properties ideal for use in the packaging industry, food, etc.

This filament has been approved as a valid filament for direct contact with food according to EU regulations (in the US, only the natural color is approved). To ensure that the final product meets the requirements, it must undergo testing in accordance with relevant regulations. These regulations define the testing conditions, which are based on the intended use of the printed object (e.g., temperature, duration of contact, type of food).

Although most of its mechanical and physical properties (stiffness, tensile strength and impact resistance, thermal stability, ...) are similar to those of ABS, there is a feature that makes it different to everyone else which is its solubility in D -Limonene, allowing to make unworkable forms a soluble support material and will be realized once the piece in D-Limonene and HIPS immerse disappears, leaving the piece without any support material with a high surface quality.

It is indicated for light and high-quality technical parts (Due to the high resolution printing) material. Extrafill HiPS filament (Polystyrene) is a bit lighter than the ABS. The temperature optimum print is 245 °C. When printed at this temperature it is necessary that the temperature of 90-100 ºC bed is to minimize the warping effect.

Besides the Extrafill HiPS filament has a very good seal so it is ideal for containing liquids without leakage. This property is due to the high thermal inertia of own Extrafill HiPS which enables a very good adhesion between layers print.

Extrafill HiPS filament is resistant to oils, fats and alkalis but not fuel. As for his post-processing and finishing it can be chrome, paint, glue and sand. HIPS supports evil UV rays, so you long exposure to the sun it discolor and become brittle. If you need a material that resists well UV light rays you must choose the ASA filament. HIPS (Polystyrene) has low electrical conductivity (10¹⁴Ω*cm), which can be used as an electrical insulator. Its properties typically used in high-frequency. As for the softening temperature HIPS it supports up to 88 °C.

General information
Material	HiPS
Format	750 g / 2500 g
Density	(ISO 1183) 1.05 g/cm³
Filament diameter	1.75 / 2.85 mm
Filament tolerance	± 0.05 mm
Filament length	(Ø 1.75 mm - 0.75 kg) ± 297 m / (Ø 1.75 mm - 2.5 kg) ± 990 m / (Ø 2.85 mm - 0.75 kg) ± 112 m / (Ø 2.85 mm - 2.5 kg) ± 373 m

Mechanical properties
Charpy impact strength	(ISO 179) 17 KJ/m²
Elongation at break	(ISO 527) 40 %
Tensile strength	(ISO 527) 26 MPa
Tensile modulus	(ISO 527) 2000 MPa
Flexural strength	(ISO 178) 40 MPa
Flexural modulus	(ISO 178) 2100 MPa
Surface hardness	-

Electrical properties
Volumetric resistivity	(IEC 93) 10¹⁶ Ω*cm
Surface electrical resistivity	(IEC 93) 10¹³ Ω

Printing properties
Printing temperature	230 - 250 ºC
Print bed temperature	90 - 105 ºC
Chamber temperature	-
Cooling fan	✗
Recommended printing speed	- mm/s

Thermal properties
Softening temperature	(ISO 306) 89 ºC

Specific properties
Transparency	✗

Other
HS Code	3916.9
Spool diameter (outer)	(0.75 kg) 200 mm / (2.5 kg) 300 mm
Spool diameter (inner hole)	(0.75 kg) 55 mm / (2.5 kg) 53 mm
Spool width	(0.75 kg) 50 mm / (2.5 kg) 53 mm

It´s a material with properties very similar to those of ABS that printing is not especially difficult to print. Nozzle temperature should be between 230 and 240 °C. As in the case of ABS, the need to use a hot bed at a temperature of about 80-100 °C. Once the printing must wait for the piece cool before removing to prevent any deformation may occur due to the printing temperature. It is also advisable to use BuildTak or Dimafix to prevent warping effect on printing.