Display Nav Left

Language:

Compare

You must be logged in to manage your wishlist.

ABS with carbon fiber (ABS CF)

Ref.: ABS-CF-NANOVIA-175-500

46.50 €

Tax excl.

Diameter

Format

Quantity

In stock 7 units available for immediate shipping.
units available for shipping in 0 - 0 days Available for shipment within 0 - 0 days

Product temporarily out of stock with these characteristics. Select another combination.

We notify you when it will be available:

Approximate delivery date: Friday 13 September

Available

Returns

Ask about this product

ABS is one of the most widely used materials for 3D printing and is used to make parts and elements that we use on a daily basis (car fenders and headlights, electrical connection boxes, containers, etc.). That is why it is not surprising that manufacturers develop new materials from ABS. ABS CF is an Acrylonitrile Butadiene Styrene reinforced with carbon fibers to improve the general mechanical properties of the plastic base.

ABS CF

Image 1: Part printed with ABS CF. Source: Nanovia.

The Nanovia ABS CF stands out from the rest of the market due to its advanced size distribution of carbon fibers in ABS. Both the distribution and the amount of carbon fiber have been carefully studied and developed by the Nanovia technicians until they reach a strand of advanced behavior. Thanks to all the above, ABS CF exerts much less wear on the nozzle of the 3D printer compared to other abrasive materials that contain carbon fiber.

On the other hand, the development of this filament has also achieved high values of mechanical strength (Tensile Modulus: 2700 MPa), 35% higher than a standard ABS, with a lesser fragility than many materials often combined with fiber of carbon.

A common problem that occurs when using ABS is the dimensional stability, especially when it comes to being in an environment with temperatures close to the softening point. The introduction of carbon fiber improves dimensional stability and reduces the coefficient of thermal expansion. All this becomes a low deformation of the pieces made (reduction of the warping effect) and a high power distribution of mechanical stress.

The Nanovia ABS CF is an ideal material to replace ABS parts that need to withstand higher mechanical stresses, higher temperature values and be resistant to impacts. In addition, the ABS CF is compatible with most 3D FDM printers on the market and with any standard nozzle (brass) of 0.4mm.

Piece for agricultural machine

Image 2: Piece for agricultural machine. Source: Nanovia

General information
Material	ABS
Format	50 g / 500 g
Density	1.08 g/cm³
Filament diameter	1.75 / 2.85 mm
Filament tolerance	± 0.05 mm
Filament length	(Ø 1.75 mm-0.5 Kg) ±192 m / (Ø 2.85 mm-0.5 Kg) ±72 m

Printing properties
Printing temperature	250 - 270 ºC
Print bed temperature	90 - 110 ºC
Chamber temperature	✗
Cooling fan	✗
Recommended printing speed	30 - 70 mm/s

Mechanical properties
Charpy impact strength	5.18 KJ/m²
Elongation at break	(ISO 527) 10 %
Tensile strength	- MPa
Tensile modulus	(ISO 527) 2700 MPa
Flexural strength	- MPa
Flexural modulus	(ISO 178) 2700 MPa
Surface hardness	-

Thermal properties
Softening temperature	90 ºC

Specific properties
Transparency	✗
Flammability classification	HB UL 94 @ 1.6 mm

Other
HS Code	3916.9
Spool diameter (outer)	200 mm
Spool diameter (inner hole)	52 mm
Spool width	55 mm

3D printing with ABS filament is a bit more complex than with the PLA filament. In the case of the ABS CF filament, it's necessary that the printing base is hot, between 90 and 110ºC. In addition, the temperature of the extruder should be between 250 and 270ºC. It should also be remembered that ABS plastic undergoes the phenomenon called "warping", which causes the first layer of the pieces to detach from the base of the 3D printer. So if you are going to print large pieces it's advisable that you use BuildTak, Kapton Tape, Magigoo or DimaFix so that the pieces don't tend to detach from the base. To ensure the dimensional stability of the parts it's advisable to use a closed 3D printer.

With ABS CF it isn't necessary to use reinforced nozzle since this filament has low abrasion. Even so it is recommended to use the Olsson Ruby Nozzle for all advanted materials.