Tribo 750 g 1.75 mm
search
  • Tribo 750 g 1.75 mm
  • Tribo 750 g 1.75 mm
  • Tribo 750 g 2.85 mm
  • Tribo 750 g 2.85 mm
  • Tribo 750 g 2.85 mm
Compare
You must be logged in to manage your wishlist.

Tribo

TRIBO-175-750
119.45 € 119.45 €
Tax excl.
Diameter
Format
Quantity

In stock 3 units available for immediate shipping.
units available for shipping in 0 - 0 days Available for shipment within 0 - 0 days

Product temporarily out of stock with these characteristics. Select another combination.

Product temporarily out of stock with these characteristics. Select another combination.

We notify you when it will be available:

Approximate delivery date: Monday 25 November
Available

Tribo filament is a material resistant to friction up to 50 times more than conventional materials used for elements such as ABS in 3D printers as it offers a response to wear. Tribo filament is designed specifically for Tribology. Tribology is the science of friction, wear and lubrication taking place during contact between solid surfaces in motion. The characteristics of a good material as the filament Tribo are to reduce friction and wear to conserve and reduce energy, achieve faster and more precise movements, increase productivity and reduce maintenance. Tribology focuses on the study of three phenomena:

  1. Friction between two bodies in motion; Understood by friction resistance during sliding movement or rolling undergoing a solid to move over another with which it is in contact body.
  2. Wear as a natural effect of this phenomenon; Burnout is a process in which the surface layers of a solid break or detach from the surface. Wear may occur by fatigue, abrasion, erosion, corrosion, by rubbing, sliding, by impact, etc.
  3. Lubrication as a means to reduce wear; Lubrication involves the introduction of an intermediate layer of a foreign material between the moving surfaces.

The design of parts or manufacturing prototypes are not detached from life assurance with Tribo filament. Tribo filament replaces the ABS to print bearings and gears 3D printers as it is designed to reduce friction, increase the wear resistance of parts and avoid lubrication.

Fuente: www.igus.eu

General information
Material Iglidur
Format 50 g / 250 g / 750 g
Density 1.21 g/cm³
Filament diameter 1.75 / 2.85 mm
Filament tolerance ± 0.05 mm
Filament length (Ø1.75 mm-0.25kg) ±85 m / (Ø2.85 mm-0.25kg) ±32 m

Electrical properties
Volumetric resistivity 10¹² Ohm/cm
Surface electrical resistivity 10¹¹ Ohm

Printing properties
Printing temperature 250-260 ºC
Print bed temperature 90-110 ºC
Chamber temperature ✗
Cooling fan ✗
Recommended printing speed 50 mm/s

Mechanical properties
Elongation at break - %
Tensile strength - MPa
Tensile modulus 1000 MPa
Flexural strength 33 MPa
Flexural modulus 1000 MPa
Surface hardness Shore 66 D

Thermal properties
Softening temperature 80 ºC

Specific properties
Transparency -

Other
HS Code 3916.9
Spool diameter (outer) 205 mm
Spool diameter (inner hole) 55 mm
Spool width 55 mm

Tribo filament can be printed on most 3D FFF / FDM printers. The bed should be heated to 90-110 °C temperature and the extrusion temperature is 250-260ºC. It is advisable to use Kapton Tape o 3DLac so that the pieces do not tend to detach from the base (warping effect). As for the interior temperature which is printed it is recommended to be controlled and there are no drafts.

Finally it is important that the 3D printer is in a well-ventilated room. The material should not be heated above 300 °C and which can form hazardous decomposition products.

Featured properties

Printing temperature
250-260 ºC
Filament diameter
1.75 / 2.85 mm
Density
1,21 g/cm³

Related products