Find the most suitable 3D printer for your needs.
We guide you to find the best option according to your needs.
Find the most suitable 3D scanner for your needs.
Contact us and we'll get it for you.
Find the most suitable filament for each application.
Find the most suitable resin for each application.
Find the most suitable powder for each application.
Find the most suitable pellets for each application.
Find the accessory you need for your 3D printer.
Find the ideal accessories for your 3D prints.
In 3D printing there are always a series of factors that depend on the user, which often cause a print to be satisfactory or failed. All factors are collected in the print profile that each user uses in each 3D print.
In the 3D FDM printing profiles, an infinite number of parameters can be modified: printing temperatures and speeds, how to manufacture the internal and external parts and all the rest of the parameters that influence 3D printing. For this reason, the most important information is discussed below when creating a print profile.
Before beginning to modify printing parameters, a series of factors that will directly influence must be taken into account:
The shape and thickness of a part directly affects the printing parameters such as speeds and layer thicknesses, since if a part has areas of reduced size, the print profile must have lower manufacturing speeds, to ensure quality of the piece.
As all users already know, each material has a range of temperatures and speeds recommended by each manufacturer, it is advisable to stay at those values to avoid possible problems, such as the appearance of calcined filament particles in the nozzle due to excess temperature, which subsequently cause the filament to jam in it.
Within the FDM 3D printers there are important differences. One of the differences that most influences the configuration of the printing profile is the type of extruder, direct or bowden, since very different values are needed in the sections of print speed, speed and retraction length and even in the flow.
Something that few users take into account is the environment where the 3D printer is located. Temperature, humidity or the existence of air currents are factors that directly affect the printing profile and in some cases the surface finish of the pieces.
One of the many advantages of 3D printing is that the same piece can be made with infinite different configurations: better or worse surface finish depending on the printing time, more resistance on one surface or another, etc. This is achieved by adapting each profile to each particular case.
Once all the above is clear, it is time to configure the profile and for this Polymaker has developed PCP (Profile Creation Process), five tests for all users to achieve the ideal print profile:
The first step is to find the ideal temperature for the material that the user needs to use. It should be started using the lowest temperature recommended by the filament manufacturer and increase it until the flow is continuous and there are no jams in the HotEnd.
Users who wish to perfectly adjust the temperature, can perform a temperature test, such as the test in the following image.
This section should correct printing errors caused by to bad flow configuration. This mismanagement can cause irregular flow due to excessive extruder pressure or filament debris across the entire surface of the part due to the wrong retraction configuration.
The layer fan is one of the most important components of a 3D printer, since with it you can get more complex geometries and higher quality surface finishes.
The following scheme shows the forces that act at the junction between layers. "F1" is the force of lifting of the material when it is in cantilever and "F2" is the force of contraction caused by the tension of the upper layer. The value of these two forces must be approximately zero to maintain mechanical and geometric stability. To achieve "F1 = 0" the layer height, the angle of overflow and the extrusion temperature must be reduced; or increase the speed of the layer fan. In the case of "F2", the force value can be minimized by increasing the extrusion temperature or reducing the extrusion speed.
Something that usually occurs when using filaments such as ABS or ASA is delamination between layers (cracking) or between the first layer and the base (warping). This occurs during printing due to the accumulation of stress between layers, caused by the action of the strength of the polymer itself (F2) and the action in the opposite direction of the adhesion of the lower layer (F1.2) or of the base itself printing (F1.1). When the forces involved in the union are not balanced, delamination occurs, as shown in the following image.
To avoid this, the user must find the ideal base temperature and have a closed 3D printer when the material to be used requires it.
Finally, to ensure that the entire surface of the printed part has a perfect finish, including the finest parts, the user must adjust the flow and cooling through the layer fan. The adjustment of the two parameters must be carried out by carefully modifying the values so as not to pass, since this can cause errors mentioned above.
All the detailed information in this article is intended for a user to get the print profile of any material, taking into account that the 3D printer is capable of offering the necessary printing parameters.
Hola, tengo una impresora vitofeli xy, y cuando imprimo una letra de 10 cm de alto por 4 cm de grosor me falla en la misma parte.El archivo stl no tiene falla, lo revisé.Relleno 20%PlaLa falla lo hace cuando ya imprimió 2 cm es en la letra S, en la parte de arriba la vuelta.Le puse primero 3 capaz en la pare y después 4 capaz y me hizo el mismo error, solo que menos visible.La imprimi más de 5 veces, de formas distintas, más capa, más relleno, de distintas formas en la cama y siempre me hace el mismo error en el mismo lugar.Espero algún consejo, gracias.
Hola Vanessa,Sin ver una fotografía del fallo nos es difícil poder decirte más. Puedes enviarnos un email a [email protected] e intentamos ayudarte.Un saludo.
Boa tarde, fiz encomenda de impressora creality, mas ainda não chegou, procuro um programa para iniciar a fazer algumas peças Podem ajudar qual o programa que deve usar ?
I have read and accept the privacy policy.