Display Nav Left

Language:

Compare

You must be logged in to manage your wishlist.

DimaFix (spray)

Ref.: DIMAFIX-SPRAY

10.25 €

Tax excl.

Format

Volume discounts

Quantity	Discount	Price
6	5% 5%	9.74 € 9.74 €
12	8% 8%	9.43 € 9.43 €
24	10% 10%	9.23 € 9.23 €

Quantity

In stock 265 units available for immediate shipping.
units available for shipping in 2 - 5 days Available for shipment within 2 - 5 days

Product temporarily out of stock with these characteristics. Select another combination.

We notify you when it will be available:

Approximate delivery date: Thursday 19 June

Available

Returns

Ask about this product

Dimafix is a fixative solution designed for the FDM/FFF 3D printing technology with heated bed in order to eliminate the effect "warping". It is considered "intelligent" because its adhesion properties vary depending on the hot bed temperature. Dimafix is available in spray format (400 ml) or in stick/pen format (90 ml).

Video 1: A demonstration of Dimafix in both formats. Source: Tu rincón 3d.

Dimafix has a binding properties up to 100 times more than conventional lacquers, thereby minimizing deformation ("warping") in large parts or materials with many internal tensions. It has been tested successfully on materials which tend to exhibit the warping effect as ABS, Nylon, FilaFlex, Polypropylene, HIPS, PVA, etc.

Adhesive power curve

There are four printing base temperature ranges that condition the adhesion power of the Dimafix spray.

Range 1: <65°C. Zone of self-detachment of the part. Adherence within this temperature range is very weak.
Range 2: 65 ºC - 75 ° C. Average adhesion area. Dimafix starts to take effect up from the temperature of 65 ºC. This temperature range it is recommended for simple parts without sharp edges or complex geometries.
Range 3: 75 ºC - 95 °C. High adhesion area. You can print any type of geometry, especially those whose base dimensions do not exceed 200 x 200mm.
Range 4: 95 ºC - 120 ºC. Maximum grip area. You can print any type of geometry and dimensions. In this range the bonding stress of the printing surface of the 3D printer with the workpiece is high, withstanding any stress concentration factor.

Adhesive power curve for the Dimafix spray

Image 1: Adhesive power curve for the Dimafix spray. Source: Dimafix.

A very valuable feature of the Dimafix adhesive solution is that the model can be easily removed after printing (as soon as the printing base cooled down), and the printing base can be easily cleaned (glass bases) since Dimafix is soluble in water. The Dimafix spray gives approximately 100 uses.

General information
Manufacturer	DIMA3D
Format	400 ml
Composition	60-70% C2H6O, 25-30% C2H5OH, 5-10% C3H8O
Caution and safety warnings	GHS02, GHS07

Other
HS Code	3305.3

To apply Dimafix should consider the following:

Shake can before applying (The boat has an inside ball to prevent clogging in the nozzle).
Ensure that the bed is below 50 ºC.
Apply at a distance of 30cm and a ventilated space.
Refer to the table with the recommended Dimafix depending on the piece to print temperatures. The product starts running from the 65ºC.
When the bed enough (<40ºC) is cooled, the pieces may peel off by themselves.
No need to remove the product from the base of the 3D printer after printing, only replace it in areas where previously printed.
If you want to clean the bed, the product can be simply removed with a cloth soaked in water.

In the following video you can see the steps carefully explained:

Danger indications:

Extremely flammable aerosol.
Pressurized container: may burst if heated.
It causes serious eye irritation.
Read the label before use.
Keep away from heat, hot surfaces, sparks, open flames and any other ignition source. No Smoking.
Do not spray on an open flame or other ignition source.
Do not pierce or burn, even after use.
Use only outdoors or in a well-ventilated place. Do not breathe aerosol.
IF IN EYES: Rinse cautiously with water for several minutes.
Protect from sunlight. Do not expose to temperatures exceeding 50 ° C / 113 ° F.