We will remain closed until January 1st due to the Christmas holidays. Orders received from Friday, December 27th will be shipped on January 2nd. Happy Holidays!

Display Nav Left

Language:

Compare

You must be logged in to manage your wishlist.

Natural PLA-90 PREMIUM

Ref.: PLA-90-175-750

34.90 €

Tax excl.

Diameter

Format

Quantity

In stock 3 units available for immediate shipping.
units available for shipping in 0 - 0 days Available for shipment within 0 - 0 days

Product temporarily out of stock with these characteristics. Select another combination.

We notify you when it will be available:

Approximate delivery date: Thursday 2 January

Available

Returns

Ask about this product

The PLA-90 PREMIUM Natural filament is a filament designed for all 3D printing users who wish to obtain advanced properties with a PLA filament. PLA-90 PREMIUM Natural is much less brittle than standard PLA and stands out for its high strength and stiffness. The main advantages of this filament are that it reduces shrinkage to a minimum and that the softening temperature is a little over 90ºC (hence its name).

The main advantages of this filament are minimizing the contraction and softening temperature is a bit higher than 90 °C (hence its name). The latter is the most prominent and well-known advantage of this filament. The standards PLA filaments having a softening temperature (Tg or glass point) of 55 °C; that is, once a piece printed with standard PLA, as is exposed to ambient temperatures of 55 °C decreases the glass temperature and happens to have visco elastic properties. (it starts to be "sticky" or slightly soft losing its mechanical properties).

This usually happens with printed parts PLA when exposed to ambient temperatures in hot weather (in excess of 55 °C), losing the desired properties. In contrast, the ABS has a Tg of 105 °C which makes parts printed with this material are resistant to room temperature, but in return the ABS is more difficult to print because it is necessary to have high temperature hot bed to avoid warping effect.

That is why the Natural PLA-90 PREMIUM emerges, which has a facility similar to printing and PLA also has a softening temperature similar to ABS (above the 90ºC, around 105 ºC). Properties that make it the ideal filament minimizing weaknesses and maximize the strengths of ABS and standard PLA.

Then in the next picture you can see a comparison between the ABS, standard PLA and PLA-90 PREMIUM Natural:

Properties of PLA-90 PREMIUM filament for 3D printing

Image 1: Properties of PLA-90 PREMIUM filament for 3D printing. Source: OrbiTech.

General information
Material	PLA
Format	50 g / 750 g
Density	1.5 g/cm³
Filament diameter	1.75 / 2.85 mm
Filament tolerance	± 0.05 mm
Filament length	(Ø 1.75 mm - 0.75 Kg) ± 207 m / (Ø 2.85 mm - 0.75 Kg) ± 78 m

Printing properties
Printing temperature	190 - 220 ºC
Print bed temperature	90 - 100 ºC
Chamber temperature	40 - 45 ºC
Cooling fan	✓
Recommended printing speed	- mm/s

Mechanical properties
Elongation at break	- %
Tensile strength	- MPa
Tensile modulus	- MPa
Flexural strength	- MPa
Flexural modulus	- MPa

Thermal properties
Melting temperature	175 ºC
Softening temperature	90 ºC

Specific properties
Transparency	✗

Other
HS Code	3916.9
Spool diameter (outer)	200 mm
Spool diameter (inner hole)	52 mm
Spool width	55 mm

Other information
mensaje prueba EN

If your printer has a fan nozzle it is recommended that you activate it for best results. If you need to print very thin and tall pieces, you will see that the PLA plastic does not give you enough time to harden each layer, so that the piece will be as if it had melted. To solve this problem we give a very simple advice, it prints at the same time at least two pieces, and place them separate at the base. Thus while the extruder is moved from one piece to another, the plastic has time to harden each layer in achieving a better result.

The adhesion of the first layer is key and probably the most important factors for good prints, so you can use Magigoo, BuildTak, Blue Tape or 3DLac. It is also advisable to set the "raft", which is to create a first thick layer, such as media, who will not suffer that contraction and on which to print the piece. The disadvantage of using the "raft" is that this first layer will have a less smooth. It is advisable to lower the density of "infill" parameter for the part to store less heat. As for the "brim" (the membrane that is created around the piece) parameter is recommended to set it to never greater thicknesses of 5mm to help the first layer will not peel. As for the interior temperature where printed it is recommended to be controlled and no drafts.

If the piece has trouble peel off the glass or printer dock to finish printing a trick widely used it is to introduce the glass along with the piece a few minutes in a refrigerator to make it easier to take off one's own piece of the bonding base.