No products

To be determined Shipping

0,00 € Tax

0,00 € Total

Check out

Product successfully added to your cart

0 products in the cart 1 product in the cart

Quantity:

Checkout

Our webstore uses cookies to offer a better user experience and we recommend you to accept their use to fully enjoy your navigation.

More information Gestionar cookies

I accept

View larger

Taulman 680 FDA

Reference:

Brand: Taulman3D

Condition: New product

13 Item Items

Diameter

Format

Quantity

69,95 €

Ask for information

Developed specifically to fulfill FDA regulation 21 CFR 177.1500 (contact with food).

Add to wishlist

More info
Data sheet
Download
Usage tips
Specifications

Taulman Nylon 680 is a filament for 3D printer made with a polymer specifically developed to meet FDA 21 CFR 177.1500. In this regulation the materials that can make containers for contact with food (except food with more than 8% alcohol) is regulated.

The Nylon Taulman 680 is designed to print in the same temperature range as other Nylons Taulman. The Nylon Taulman 680 is more transparent than nylon 645, which allows non-destructive visual inspections of the printed area. The Nylon Taulman 680 is less flexible than nylon 645, as is intended to support a long list of medical uses.

Taulman Nylon 680 spools come with 2 QR codes. Through one of them you can access technical information needed to use this filament on your 3D printer. And the second is for product traceability.

In the following article you can see the main differences of nylon Taulman 3D filaments.

Elongation at break (%)	34
Tensile strength (MPa)	47
Softening temperature (ºC)	93
Alimentary use	Alimentary use
Medical use	Medical use
Hide color variations	(Hide color variations)

Nylon 680 Datasheet

Download

Nylon 680 Safety Datasheet

Download

The recommended temperature of 252 °C extruder is. In no case should not be used in the 3D printer filament at a higher temperature of 255 ° C.

To ensure the correct adhesion of the Taulman 680 FDA to the base, it's recommended to use BuildTak, DimaFix, PrintaFix or Magigoo PA. In addition to this adhesive it has been developed exclusively for nylon filaments and can be used with a microperforated base, PEI sheets or Kapton Tape can be used. It must be ensured that the adhesion of the first layer is firm and strong to prevent it from peeling off during 3D printing.

During the printing process can you see smoke coming from the extruder, do not panic, it's just water vapor. This is because the nylon has a great capacity to absorb moisture. For this reason we recommend that after use in your 3D printer save your coil nylon bag with the absorbent silica in the original bag. Close the bag so that it is the best possible sealed and store in a dry place.

General information
Manufacturer	Taulman (USA)
Material	Nylon (PA)
Format	Pack of 50 g Spool of 0.45 kg
Density	1.25 g/cm³
Diameter of filament	1.75 or 2.85 mm
Diameter tolerance	±0,05 mm
Filament length	±149 m (Ø 1.75 mm-0.45Kg) ±56 m (Ø 2.85 mm-0.45Kg)
Color	Bright white
RAL/Pantone	-
Print settings
Printing temperature	250-252ºC
Print bed temperature	30-65ºC
Chamber temperature	Not necessary
Cooling fan	Not recommended
Mechanical properties
Izod impact strength	-
Charpy impact strength	-
Elongation at break	34%
Tensile strength	47 MPa
Tensile Modulus	-
Flexural strength	-
Flexural modulus	-
Surface hardness	-
Thermal properties
Softening temperature	93ºC
Melting temperature	210ºC
Specific properties
Transparency	Low (30%)
FDA certification	Yes
Inflammability (UL 94 HB)	Yes
Additional Information
HS Code	3916.9
Diameter coil (outer)	200 mm
Diameter coil (inner hole)	50 mm
Coil Width	50 mm

* The typical values detailed in this table should be considered as a reference. Actual values may vary depending on the 3D printer model used, part design and printing conditions. We recommend confirming the results and final properties with own tests. For more information you should consult the technical data sheet of the product.