Display Nav Left

Language:

Compare

You must be logged in to manage your wishlist.

LayWoo-D3

Ref.: LWOO-175-R250

22.90 €

Tax excl.

Diameter

Format

Quantity

In stock 6 units available for immediate shipping.
units available for shipping in 0 - 0 days Available for shipment within 0 - 0 days

Product temporarily out of stock with these characteristics. Select another combination.

We notify you when it will be available:

Approximate delivery date: Friday 13 September

Available

Returns

Ask about this product

Laywoo-D3 is a filament for 3D printing made from wood fibers (40%) and a binding polymer, that recreates a surface finish and similar to the texture of wood.

The pieces obtained with Laywoo-D3 filaments can be sanded and painted. Also, if you modify the extrusion temperature slightly changes the surface color of the piece. The lower the extrusion temperature is obtained a lighter color and if the extrusion temperature is higher a surface color darker figure is obtained.

Parts 3D printed with the LayWoo-D3 material

Image 1: Parts 3D printed with the LayWoo-D3 material. Source: Kai Parthy.

Laywoo-D3 is especially suitable for 3D printing of decorative elements. Since the combination of the new geometries that can be manufactured through 3D printing and the various possibilities of surface finish offers Laywoo-D3 will enable you to create innovative decorative pieces.

Unlike filament Timberfill Light Wood Tone this filament recreates a darker finish.

Once the Laywoo-D3 used in the 3D printer filament, it is recommended to remove the remaining filament and proceed to extrude PLA for one minute at high temperature (230 ° C). This will eliminate the internal printhead any remaining Laywoo-D3 which can cause jams the nozzle. In the tab tips you can use encontrarar more information about how to use this in your 3D printer filament and get the best printing results.

General information
Material	PLA
Format	50 g / 250 g
Density	1.24 g/cm³
Filament diameter	1.75 / 2.85 mm
Filament tolerance	± 0.1 mm
Filament length	(Ø1.75 mm, 0.25 kg) ±83.8 m / (Ø2.85 mm, 0.25 kg) ±31.6 m

Printing properties
Printing temperature	180 - 250 ºC
Print bed temperature	40 ºC
Chamber temperature	✗
Cooling fan	✓
Recommended nozzle diameter	Min. 0.4 mm

Mechanical properties
Elongation at break	- %
Tensile strength	- MPa
Tensile modulus	- MPa
Flexural strength	- MPa
Flexural modulus	- MPa
Surface hardness	-

Thermal properties
Softening temperature	55 ºC

Specific properties
Transparency	✗

Other
HS Code	3916.9
Spool diameter (outer)	200 mm
Spool diameter (inner hole)	125 mm
Spool width	30 mm

Printing with this filament is not as simple as with other types of plastics. You need to follow a few steps to avoid problems during and after printing.

You need to use a nozzle at least 0.35mm in diameter, although it is best to use a 0.5mm diameter nozzle. Your printer should have the option of heating the base since it needed 40ºC for the phenomenon of "warping" does not occur. In addition to the base you must place Kapton Tape or 3DLac to ensure adhesion between the base and the workpiece.
The filament is easily deformed, so it is advisable that the feeder your 3D printer you reduce the pressure on the filament so there are no excessive marks on the LayWoo-D3 filament. (It is also recommended print with direct drive to prevent facture filament itself because of its delicacy).
The optimum temperature of the extruder may vary between 180 and 250C, but below 200C run the risk of jamming your extruder.
Once you have finished printing, remove the LayWoo-D3 filament your 3D printer and load PLA filament for about 30 seconds to clear any remaining LayWoo-D3 that may remain within the extruder. If you do this you run the risk that the extruder is locked next time you want to print.

Masterspool format

The 250 g. format of the LayWoo-D3 filament can sometimes cause problems during the printing process because it does not include a spool that helps the correct supply of material from the 3D printer.

To avoid this type of problem when printing this and other filaments that are sold in masterspool format you can use a variable spool holder. Thanks to the use of this device, all kinds of tangles and overlaps derived from the absence of a spool are largely avoided.