Product successfully added to your cart
0 products in the cart 1 product in the cart
Our webstore uses cookies to offer a better user experience and we recommend you to accept their use to fully enjoy your navigation.
More information Gestionar cookiesLaywoo-D3 is a filament for 3D printing made from wood fibers (40%) and a binding polymer, that recreates a surface finish and similar to the texture of wood.
The pieces obtained with Laywoo-D3 filaments can be sanded and painted. Also, if you modify the extrusion temperature slightly changes the surface color of the piece. The lower the extrusion temperature is obtained a lighter color and if the extrusion temperature is higher a surface color darker figure is obtained.
Laywoo-D3 is especially suitable for 3D printing of decorative elements. Since the combination of the new geometries that can be manufactured through 3D printing and the various possibilities of surface finish offers Laywoo-D3 will enable you to create innovative decorative pieces.
Unlike filament Timberfill Light Wood Tone this filament recreates a darker finish.
Once the Laywoo-D3 used in the 3D printer filament, it is recommended to remove the remaining filament and proceed to extrude PLA for one minute at high temperature (230 ° C). This will eliminate the internal printhead any remaining Laywoo-D3 which can cause jams the nozzle. In the tab tips you can use encontrarar more information about how to use this in your 3D printer filament and get the best printing results.
Machinable | Machinable |
Fiber reinforced | Fiber reinforced |
Hide color variations | (Hide color variations) |
Printing with this filament is not as simple as with other types of plastics. You need to follow a few steps to avoid problems during and after printing.
The 250 g. format of the LayWoo-D3 filament can sometimes cause problems during the printing process because it does not include a spool that helps the correct supply of material from the 3D printer.
To avoid this type of problem when printing this and other filaments that are sold in masterspool format you can use a variable spool holder. Thanks to the use of this device, all kinds of tangles and overlaps derived from the absence of a spool are largely avoided.
General information | |
---|---|
Manufacturer | Kai Parthy-LayFilaments (Germany) |
Material | Fibers of wood with polymer of union |
Format | Pack of 50g Roll of 250g |
Density | - |
Diameter of filament | 1.75 or 2.85 mm |
Diameter tolerance | ±0,1 mm |
Filament length | - |
Color | Dark wood |
RAL/Pantone | - |
Print settings | |
Printing temperature | 180-250ºC |
Print bed temperature | 40ºC |
Chamber temperature | Not necessary |
Cooling fan | Recommended |
Nozzle diameter | >0.40 mm |
Mechanical properties | |
Izod impact strength | - |
Charpy impact strength | - |
Elongation at break | - |
Tensile strength | - |
Tensile Modulus | - |
Flexural strength | - |
Flexural modulus | - |
Surface hardness | - |
Thermal properties | |
Softening temperature | - |
Melting temperature | - |
Specific properties | |
Transparency | Opaque |
Additional Information | |
HS Code | 3916.9 |
Diameter roll (outer) | 200 mm |
Diameter roll (inner hole) | 125 mm |
Roll width | 30 mm |
* The typical values detailed in this table should be considered as a reference. Actual values may vary depending on the 3D printer model used, part design and printing conditions. We recommend confirming the results and final properties with own tests. For more information you should consult the technical data sheet of the product.
36,36 €
36,36 €
36,36 €
36,36 €
7,50 €
26,00 €
28,92 €
28,92 €
28,92 €
33,02 €
32,00 €
38,25 €
38,25 €
35,00 €
16,75 €
22,90 €
22,90 €
38,25 €
37,97 €
36,36 €
36,36 €
36,36 €
36,36 €
22,50 €
56,99 €
23,95 €