1
  • $options.id_post:
  • $options.slug:
  • https://filament2print.com/gb/blog/_.html
  • es
  • gb
  • pt
  • fr
  • Polish Kit Proto-Pasta

    New product

    5 Items

    20,95 €tax excl.
    25,35 €tax incl.

    Ask for information

    The Polish Kit is the set of essential components to give a smooth and shiny finish.

    The Polish Kit is the set of essential components to give a smooth and shiny finish to the printed pieces with filaments containing metallic fibers (PLA-Stainless SteelPLA-Magnetic or Copper HTPLA).

    Filaments containing metal fibers behave as metals in terms of surface finish, so they can be sanded and polished without any problem. The Polish Kit contains everything necessary to post-process the printed pieces, both by sanding the surface and polishing it. To make the sanding has 5 sheets of sandpaper (100x125 mm) of different grain: 400 (yellow), 600 (gray), 1200 (blue), 4000 (pink), 6000 (teal), 8000 (white). Thanks to this set of sanding sheets, an extremely smooth and smooth surface finish can be obtained.

    100x125mm sandpaper

    Image 1: 100x125 mm sandpaper

     

    To polish, it has: a 100mm diameter muslin disk to attach to a drill, a polishing cotton shaft and a polishing component (Fabulustre).

    muslin disk

    Image 2: Muslin disk

     

    Before using the muslin disc or the polishing spindle, a bit of the polishing component should be applied to them, then polish the desired part. This treatment must be carried out by firmly gripping the part and the polishing tool, with continuous movements without excessive pressure, so as not to overheat the material (possible deformation), and often checking the surface condition to control the finish, until the desired one is achieved. .

    Polishing component

    Image 3: Polishing component

     

    If you need only the sanding papers, select the combination of Polishing Paper Set, which contains 5 sandpaper (213x275 mm) with all the different grains needed to achieve a smooth and smooth finish of the pieces printed with materials containing metallic fibers such as Copper HTPLA:

    - 400 (yellow)

    - 600 (grey)

    - 1200 (blue)

    - 4000 (prink)

    - 6000 (teal)

    - 8000 (white)

    213x275 mm sandpaper

    Image 4: 213x275 mm sandpaper

     

    Below, two videos are shown where you can see how to perform the sanding and polishing processes correctly.

    Video 1: Sanding process. Source: Proto Pasta

     

    Víieo 2: Polishing Process. Source: Proto Pasta

    During the assembly of the muslin disc in the screw, check that it's tight enough, as well as check that the screw fixing to the drill is tight enough so that it doesn't loosen during polishing. Apart it's recommended to always use nitrile gloves and safety glasses during the polishing process to prevent possible accidents since it's a process where rotating elements are used that can produce chafing or splash polish that can reach the eyes.


    • Manufacturer: Proto-Pasta.


    The Polish kit contains:



    • 5 sandpaper (100x125 mm): 400 (yellow), 600 (gray), 1200 (blue), 4000 (pink), 6000 (teal), 8000 (white).

    • 1x Muslin disk.

    • 1x polishing cotton shaft.

    • 2x Adapter shaft for drill.

    • 1x Polishing component.



    The Polishing Paper Set contains:



    • 5 sandpaper (213x275 mm): 400 (yellow), 600 (gray), 1200 (blue), 4000 (pink), 6000 (teal), 8000 (white).

    30 other products in the same category: