Modifi3D Tips Kit

KIT-TIPS-MODIFI3D

New product

1 Item

Warning: Last items in stock!

17,45 €
17,45 €

Ask for information

Replacement of the interchangeable tips for the finishing tool of parts manufactured by 3D printing FFF/FDM Modifi3D.

Modifi3D is the finishing tool for 3D printing, specially designed to finish, repair and modify 3D parts at a low cost.

It is lightweight, compact and easy to use. It is designed to replace much of the sanding, scraping and lace, or what is the same, to facilitate the post-processing of the pieces printed in 3D.

It is composed of 4 different interchangeable tips. These tips have a special coating to prevent the plastic from sticking.

Modifi3D Tips Kit

Image 1: Modifi3D Tips Kit

 

The Tip Kit for the Modifi3D is a spare created to exchange only the tips without having to buy a new Modifi3D tool once the initial tips have worn out, since like all tools, with use they present wear or can suffer a blow and break. It's advisable to have a Kit of tips to greater than the tips that includes the Modifi3D, to always be safe and not penalize time in the post-processing if any problem occurs with any of the Modifi3D tips.

Interchangeable tips make it easy to choose the right tool for the job.

Finishing tool for 3D printing

Needle: Ideal for cleaning small holes or for detailed refinements of layers in hard-to-reach places.

Finishing tool for 3D printing

Knife: For cutting and removing sections including removing racks and rafts from your 3D printing.

Finishing tool for 3D printing

Spoon: Prefect to remove threads and imperfections from holes or interior recesses. Can also be used to mix surfaces.

Finishing tool for 3D printing

General purpose tip to define internal details and make larger holes.

In the following review you can see the operation of MODIFI3D as well as all its details:

Quick change tips:


Changing the finishing tips is really simple:



  1. Unplug the USB and allow it to cool completely.

  2. Unscrew the lock nut and remove the tip.

  3. Push the replacement tip completely and tighten the locking nut.

  4. Plug in the USB again.



Tips for cleaning the finishing tips of MODIFI3D:


To clean the interchangeable tips, we recommend using a damp sponge to remove any plastic residue from the tips. To make it easier it is better that the tips are a bit hot. (At a temperature that can not cause burns, they should be allowed to cool for a while until they reach a safe temperature). Do not use abrasive cleaners as they may damage the special tip coating.


Problem solving:



  1. MODIFI3D WITHOUT WARM. If this happens you should try plugging it into another USB socket. The USB may not be providing enough power to work properly. The most common USB 2.0 or 3.0 is recommended. It is important that the USB port is below 1A, because if the current is higher it may prevent the sleep mode from working properly.

  2. MODIFI3D IS NOT REACHING 450ºC. After pressing the metal switch, MODIFI3D automatically heats up to 300ºC. However, for the temperature to rise to 420-450 ° C, continue to touch the metal switch until the required temperature is reached. When the switch is released, MODIFI3D will start to cool down and after 25 seconds it will go into sleep mode, the light will turn off and the tip will start to cool.

  3. MODIFI3D DOES NOT GO TO REST MODE. MODIFI3D will stop automatically after not being used for 25 seconds. However, if the USB port is not supported, MODIFI3D will not stop and will continue to heat up to 420-450 ° C. This can happen with some USB ports and wall plug adapters, for example in the Apple iPad and iPhone wall adapters. It is recommended to use USB 2.0 or 3.0 that is less than 1A.

  4. THE ON / OFF SWITCH DOES NOT WORK. The touch switch does not have an "off" function. The tool will stop automatically after not being used for 25 seconds. Gently tap the switch to activate or wake MODIFI3D. Always unplug USB if MODIFI3D is not being used.

  5. MODIFIED BUTTON DOES NOT PRESS. The button is actually a touch switch and does not press. DO NOT attempt to push or push the switch, as this may damage the tool. Simply tap the switch to activate it.


The cover of the Modifi3D must be removed by pulling it, if unscrewed the tip is also unscrewed, which will cause the tool to malfunction.



Video 1: Modifi3D Tips Kit

  • Fabricant: Modifi3D

  • Model: Modifi3D Tips Kit

  • The kit contains 4 interchangeable tips: Needle, Knife, Spoon y Point.

30 other products in the same category: