Posted on 13/12/2017
What is the flow of 3D printing and how to adjust it
Tips

In this article we are going to comment on what the flow is as well as the importance it has in 3D printing. In addition, it explains how to calibrate this parameter so that the 3D printer gives the best possible results.

Flow of a 3D printer

The flow is the quantity (volume to be more precise) of filament that passes through the extruder ebased on the selected printing parameters to make a model. The calculation of the flow is carried out automatically by the 3D printer according to the Steps/mm that the 3D printer manufacturer establishes for the extruder motor, depending on the diameter of the filament and the exit diameter of the nozzle.

How to calibrate the 3D printer before an extruder change

If the extruder is changed or modified, for example by an E3D Titan Aero, the Steps/mm of the extruder motor must be adjusted.

E3D Titan Aero extruder

Image 1: E3D Titan Aero extruder. Source: E3D

The first thing is to know how many Steps/mm the 3D printer uses. This is reflected in the part of "Control>Movement>Extruder" In this case the value is 104.5 Steps/mm.

Steps/mm of extruder

Image 2: Steps/mm of extruder

Two marks are made on the filament, separated 20 mm and 25 mm from the start of the extruder.

Markings on the filament to calculate the correct number of Steps/mm

Image 3: Markings on the filament to calculate the correct number of Steps/mm

 The 20 mm filament moves from the control screen in the movement section.

Move the filament 20mm

Image 4: Move the filament 20 mm

Next, it's checked whether the displacement made by the extruder motor is correct. If not, the error is measured with a caliber to correct it. With all the above data and using the following formula we obtain the correct Steps/mm for the extruder motor.

Steps/mm flow formula

Image 5: Steps/mm flow formula

At the end of the calculation, you only have to modify the Steps/mm in the control screen and save the new data.

On the other hand, all the 3D lamination softwares have a section where to modify the flow quantity (flow rate) since the densities change between the different materials that exist in the world of 3D printing FDM/FFF. This rate is very important when it comes to achieving both the desired surface finish and the actual dimensions of the CAD design, because otherwise, it will be very complicated. manufacture of pieces that fit together or connected with others.

Before adjusting the flow, prepare the 3D printing correctly

Before explaining the adjustment of the flow rate parameter, we would like to remind you of a series of tips to always keep in mind before making a 3D printing. Always check the state of the nozzle, that doesn't present an abusive wear of the tip or that has dirt both internally and externally. Check that the extrusion temperature is recommended by the filament manufacturer, because if this recommendation isn't met, the flow calibration will be ineffective and a good result will never be achieved. Finally, and perhaps most importantly, the base must be well leveled and calibrated so that the printed model doesn't have dimensional deviations in the axis parallel to the printing base (z-axis).

The cube test for adjusting the print flow rate

To adjust the parameter of the flow rate, the cube test must be performed. This test consists in printing a hollow cube and without the upper face, to verify that the thickness of the lateral faces corresponds to those of the design.

Flow Calibration Cube

Image 6: Flow Calibration Cube

In our case we have printed a cube with a side face thickness of 0.80 mm, designed by 3D_MaxMaker that you can find in Thingiverse. The printing parameters are: nozzle of 0.40 mm, width of layer 0.80 mm (to create two outer layers and make the measurement more accurate) and flow rate of 100 %.

Flow rate 100%

Image 7: With 100 % flow rate the cube is oversized

When using PLA with 100 % flow rate (recommended 90 %) we have obtained a measurement of 0.88 mm, clearly oversized. To correct this deviation we will apply the following formula:

 

Formula to calculate the necessary flow for any material

Image 8: Formula to calculate the necessary flow for any material

Obtained the new flow rate (90 %) only remains to modify the parameter in the 3D lamination software that is used, in our case the Cura 3D.

Flow rate 90%

Image 9: Modify the flow rate to 90 %

And re-print the cube to verify that the measurements obtained with the new flow rate are correct.

Correct measurements when calculating the flow rate required for the PLA

Image 10: Correct measurements when calculating the flow rate required for the PLA

As we have said before, the density of the materials used in 3D printing isn't the same, so for each material and manufacturer it's advisable to make this adjustment.

By performing this simple correction process all 3D prints that are made will gain both surface quality and dimensional proportionality.

In summary, the flow is one of the most forgotten parameters in 3D printing FDM being this one of the most important to achieve successful parts.

Comments (11)

Write comment
    • Avatar
      Vermunt Dominique mar 27, 2019

      Bonsoir
      Merci pour votre commentaire
      je ne peux pas avoir axer a leeprom dans repetier
      et pronterface non plus
      si vous avez une solution merci
      Cordialement
      Dominique

      • Avatar
        Filament2print abr 1, 2019

        Envoyez-nous votre problème en détail à la section contact. Salutations

    • Avatar
      Carlos nov 7, 2019

      Buen articulo. Lo primero que deberíamos de hacer siempre antes de empezar a imprimir una pieza es hacer calibraciones de flow, hay mucha diferencia entre filamentos de distintas marcas.

      Saludos!

      • Avatar
        Renato jul 5, 2020

        Cuál será el orden correcto?

        Yo diría el siguiente.

        Cubo XYZ,
        Retracción
        Torre de Temperatura,
        Flujo.

    • Avatar
      Guillermo abr 17, 2020

      Hola, creo que hay un error en el párrafo inferior a la imagen 6, el ancho de capa debería ser 0,4 mm y no 0,8 como dice.

    • Avatar
      carlos jun 4, 2020

      Buenos dias, después de ajustar el flow, las paredes si que miden 0,8 pero el cubo deja de medir 20x20 para medir 19,8 o cosa así. Es normal? hay algo mas que ajustar?

      • Avatar
        Adrian jul 21, 2020

        Creo que tendrás que ajustar mínimamente el flow con este nuevo valor y aplicando la misma fórmula.

        Paso 1. 100% flow - (0.8mm y la impresión real) --> Flow1
        Paso 2. Flow1 - (20 mm y la impresión real 19.2) --> Flow nuevo
        ...

        A la segunda o la tercera estaremos con el valor de flow perfecto.

    • Avatar
      Eve nov 18, 2020

      Yo imprimo cubo de calibración y de altura me da los 20 mm pero en eje x, y me da 17 mm, ya calibre los pasos y la correa está ok.. Que podría ser? Ya no se que más ajustar

    • Avatar
      Lucia abr 4, 2021

      A mi me pasa que pongo a calentar el pla y automaticamente comienza a salir por la boquilla plastico, eso me afecta la retracción he cambiado la retraccion y no ha funcionado, cambie la temperatura y tampoco, he cambiafo el flujo a 90 y tampoco obtuve resultados, cambie el nozzle y tampoco es eso, es una anet a8, parece un problema tonto pero a causa de eso todo lo que imprimo lo hace con retraccion, he llegado a cambiarle el motor E, pero ya nose como solucionarlo, algun consejo?

      • Avatar
        Filament2Print abr 5, 2021

        Hola Lucía. Probablemente no es un problema de configuración, sino de rendimiento térmico del hotend. Para evitar el goteo durante el calentamiento es importante que la zona fría y caliente del hotend estén bien definidas. Si aplicas un poco de pasta térmica en la unión del heatbreak y el disipador probablemente mejore el problema. Además, asegúrate de que el ventilador que refrigera el hotend funciona correctamente.

Leave a comment