1
  • $options.id_post:
  • $options.slug:
  • https://filament2print.com/gb/blog/_.html
  • es
  • gb
  • pt
  • fr
  • Premium Blue HiPS (Polystyrene) View larger

    Premium Blue HiPS (Polystyrene)

    Orbi-Tech

    New product

    21 Items

    31,95 €tax excl.
    38,66 €tax incl.

    Ask for information

    Blue thermoplastic high impact resistance. It can also be used as support material.

    Premium Blue HIPS Filament (High Impact Polystyrene) is a thermoplastic obtained by polymerizing high impact resistance. It is known as "High Impact Polystyrene" and used as support material ABS or PLA prints.

    Although most of its mechanical and physical properties (stiffness, tensile strength and impact resistance, thermal stability, ...) are similar to those of ABS, there is a feature that makes it different to everyone else who is their solubility in D-Limonene, allowing to make unworkable forms a soluble support material and will be realized once the piece in D-Limonene and HIPS immerse disappears, leaving the piece without any support material with a high surface quality.

    It is indicated for light and high quality technical parts material. Premium Blue HIPS filament is a bit lighter than the ABS, which is why it can be printed at a temperature slightly lower. The temperature is 230C optimal printing. When printed at this temperature it is necessary that the temperature of 90-110 bed is to minimize the warping effect.

    Premium Blue HIPS (Polystyrene) filament is resistant to oils, fats and alkalis but not fuel. As for his post-processing and finishing it can be chrome, paint, glue and sand. HIPS supports evil UV rays, so long exposure to sun fade and become brittle him. It has low electrical conductivity, so it can be used as insulation. Its properties typically used in high-frequency. As for the softening temperature HIPS supports up 95ºC.

    It´s a material with properties very similar to those of ABS that printing is not especially difficult to print. Nozzle temperature should be between 230 and 235 °C. As in the case of ABS, the need to use a hot bed at a temperature of about 110 °C. Once the printing must wait for the piece cool before removing to prevent any deformation may occur due to the printing temperature.

    General information
    ManufacturerOrbitech (Germany)
    MaterialHiPS (High Impact Polystyrene)
    FormatSpool of 750g
    Density1.04 g/cm3
    Diameter of filament 1.75 or 2.85 mm
    Diameter tolerance ±0,1 mm
    Filament length ±299 m (Ø 1.75 mm-0.75Kg)
    ±113 m (Ø 2.85 mm-0.75Kg)
    ColorBlue
    RAL/Pantone-
    Print settings
    Printing temperature 230-235 ºC
    Print bed temperature 90-110 ºC
    Chamber temperature Not necessary
    Cooling fan Not recommended
    Mechanical properties
    Izod impact strength -
    Charpy impact strength 13 KJ/m2
    Elongation at break 20-65 %
    Tensile strength -
    Tensile Modulus 2250 MPa
    Flexural strength -
    Flexural modulus 2250 MPa
    Surface hardness Shore 65D
    Thermal properties
    Softening temperature 95ºC
    Melting temperature -
    Additional Information
    Transparency Opaque
    Información adicional
    HS Code3916.9
    Diameter coil (outer) 200 mm
    Diameter coil (inner hole) 52 mm
    Coil Width 55 mm


    * The typical values detailed in this table should be considered as a reference. Actual values may vary depending on the 3D printer model used, part design and printing conditions. We recommend confirming the results and final properties with own tests. For more information you should consult the technical data sheet of the product.

    8 other products in the same category: